If a hole in an Air Mattress threatens your sleeping comfort, you should repair it as soon as possible.
Super glue can be used to seal up cracks in loungers and inflatable mattresses. So, how do you fix a hole in an air mattress with super glue?
Fixing a hole in an air mattress may seem impossible, but it can be done easily with super glue. First, take a piece of duct tape and place it over the affected area.
Next, cut a piece of super glue about two inches long and place it over the duct tape. Then, apply some pressure to the super glue until it’s completely covered.
Finally, let the glue dry overnight before using the inflatable mattress again.
Can You Use Superglue To Fix An Air Mattress?
Contents
Find the Hole
You can’t mend a mattress until you find the leak.
If you’re having trouble locating the puncture, the bubbler may have popped off the mattress and the hose may be collapsed under your bed.
Once you’ve located the hole, you can repair it with super glue.
That is why your first step should be to locate the hole using a flashlight and a ruler or yardstick.
Holes in an air bed usually occur in the following places: underneath the bed near the pump; on the headboard; and where the air tubes connect to the valve or pump.
This is because when you inflate the beds, you press down on the bed and puncture it in several places as the air escapes from the hole.
As a result, progressively inflate the bed until the bubbles stop rising to the surface as you blow into the tube that is connected to the valve or the pump.
Then, when the air you inflate into the bed stops bubbling, you have punctured the mattress at the location of the leak and you should now proceed to fix it.
Another method for locating the leak is to plug up the nozzle of the air pump with a cloth and then deflate the bed by switching off the electricity to the pump.
You will see bubbles or froth coming out of the hole in the bed as the leaking air escapes through the nozzle of the pump.
Fix Small Holes
Deflate your air mattress by switching off the electricity to the pump and unplugging it from the socket.
Place the mattress on a flat floor and then check all around its perimeter for pinhole leaks in the fabric by using a bright light to look for air bubbles around the outside of the mattress.
Larger holes may need more effort to repair than smaller ones.
Locate the previously punctured part of the bed and apply a dab of super-glue around the hole and cover it with a piece of duct tape.
Using a paper napkin or a soft cloth, cover the adhesive tape to seal it completely to prevent the leaking of air from inside the bed.
Test
If you don’t give enough time to the glue to dry, the vacuum effect may prevent the glue from sealing the hole.
Air leaks detected in small areas may be repaired with super glue.
Small holes can be repaired with a dab of super glue placed around the hole and covered with a cloth or paper napkin.
This approach works well when the hole is too small to allow the plug of the nozzle of the air pump to be drawn inside.
You may need to give it between one and two hours for the glue to dry before testing the mattress again to see if you’ve sealed the hole successfully.
When the glue has dried, plug up the nozzle of the inflatable device with the plug or a paper towel or a cloth so that the vacuum effect is prevented from drawing the air out of the glued patch inside the mattress.
What Other Methods Can You Use to Fix Holes in Air Mattress?
Making Use of the Patch Kit
When there are holes in an air mattress that cannot be patched with super glue, a patch kit can be used to repair them.
The main problem with utilizing the patch kit is that it takes some time and patience to apply the patches.
Using Nail Polish
You didn’t believe nail polish could come in handy in patching a hole in your inflatable bed did you.
It turns out it does when you don’t have access to the patch kit and you are in a hurry to get the leaking problem fixed quickly.
It is, however, another of those temporary remedies that may not serve the purpose perfectly.
Fixing larger holes is a challenge because duct tape may only seal small holes.
The duct tape may not be able to hold the beads of super glue in place around the hole.
Making Use of Duct Tape
Another quick fix for repairing a punctured inflatable bed is to make use of a roll of duct tape, which comes in many colors these days.
This procedure is time-consuming, tedious and requires a bit of skill to be able to apply the tape effectively around the edges of the puncture without tearing it open.
All you have to do is cover the entire area of damage on the inflatable bed with a section of duct tape and then stretch it out as much as possible to cover the affected area completely.
Inflate the mattress, listen for leaks and make sure no air is escaping from the puncture before applying a second layer of tape over the damaged area to make sure it’s covered completely.
Cut enough duct tape so that you can cover at least 2 inches more on each side than the damaged area so that you have extra material to work with in case you need to make adjustments.
The more duct tape you apply, the better the chances of holding the bead of superglue in place while the mattress is inflated.
Inflate the airbed and test to see if you have successfully sealed the puncture by using a small object to push through the fabric and feel for any resistance or any bubbles of air.
What Should You Do If Super Glue Isn’t Enough?
For repairing mattresses with minor damage, super glue may be sufficient.
However, it is when the damage becomes worse that you may need to consider using other methods to repair punctured air beds or replacing the entire unit altogether.
If your super glued mattress holes continue to leak air after several hours or days, then you should consider purchasing a new unit instead of wasting time trying to repair it over and over again.
The good news is that these kits are often compact, making storage a breeze and they can be carried along anywhere you go without having to worry about where to store them.
They come with huge arrays of tools to fix all kinds of inflatable products ranging from toys to beach balls to boats and even cars.
Also Read: Is Krazy Glue the Same As Super Glue?
Conclusion
Knowing how to repair a hole in an air mattress or a deflated air bed can save you a lot of money and help you prolong the life of your investment.
Taping minor holes with duct-tape or using a super glue kit is a good fix for minor repairs, but for bigger holes, you may need to consider replacing the airbed instead.
It’s also a pocket-friendly gadget and can be purchased at a fraction of the original price if you know where to find the best deals online.
The only thing left to say now that you know everything about repairing an air bed is that safety should always come first.
